Recent posts

#2
Layout Issues / Re: Bleed in PDF for Amazon KD...
Last post by Nermander - May 20, 2025, 08:16:57 PM
Reading the specification, I don't think they support the trimbox and bleed outside that, you need to make your pages "oversize" and create the bleed using margins. They are saying they just cut away a bit on every side.

QuoteWhen a book is printed, all pages are trimmed to the selected trim size by cutting 0.125" (3.2 mm) from the top, bottom, and outside edges. In order for objects on your page to reach all the way to the edge of the page, those objects must extend past where the page will be trimmed by 0.125" (3.2 mm). This means you need to increase your page size beyond where it will be trimmed.

So don't use Scribus bleeds.
#3
Layout Issues / Re: Bleed in PDF for Amazon KD...
Last post by a.l.e - May 20, 2025, 06:35:24 PM
#4
Raster and Vector Graphics / Re: Change Color of SVG
Last post by a.l.e - May 20, 2025, 06:31:53 PM
ah, and if you want to systematically replace a color with a different one, there is "edit > replace color"...
#5
Layout Issues / Re: Bleed in PDF for Amazon KD...
Last post by AdmFubar - May 20, 2025, 06:19:13 PM
Are you doing a print or ebook publication? any errors in the preflight if pdf output?

what is the error message that amazon gives you?

In the PDF export window, in the prepress tab, bleed section, is the "use document' bleed checked? and if not, are there different values used for the bleed there?


you may also want to take a look here;

https://www.kdpcommunity.com/s/question/0D58V00009DCHdaSAH/bleed-issues?language=en_US
#6
Layout Issues / Bleed in PDF for Amazon KDP
Last post by IanicM - May 20, 2025, 03:36:59 PM
Hi, I've been using Scribus to create an atypical novel, and it's going great, until Amazon KDP rejected my PDF several times because of the bleed.

I've made it in many variations, but none of them were accepted by KDP.
My book is 6x9.

At first, Amazon support told me my book needed to be instead 6.125 x 9.25. I reformatted the book (all 291 pages) to fit this, but it was again rejected. (Amazon doesn't tell you specifics, just that the bleed is no good.)
I went back to my 6x9 book, added BLEED 0.125 (Outside, Top, Bottom) and adjusted all the pages. Exported that.

Again, the KDP was rejected.

If I look at the Amazon Preview, I can clearly see why. Whether it is a 6x9 or 6.125x9.25, there is a white line (the BLEED) around my pages. ( see attached image )

I also tried the PDF export setting: Pre-Press – Toggle ON – Use Document Bleeds.
This time there were no white edges all around, but Amazon gave me tons of margin errors.
I'm guessing the PDF option "Use Document Bleed" is cutting the bleed space, and then KDP is also cutting a new BLEED in the PDF.

Now I am at a lost. Does someone have experience with Bleed and KDP?
#7
Raster and Vector Graphics / Re: Change Color of SVG
Last post by hibert42 - May 20, 2025, 11:41:18 AM
Nice! Again I did not know and now I am smarter! Thats helps a lot!
#8
Raster and Vector Graphics / Re: Change Color of SVG
Last post by a.l.e - May 19, 2025, 10:10:20 PM
If the svg is imported into Scribus, it's not much more than a group of shapes.

You can select single items in a group by holding down the alt key (or just ungroup it and regroup it later)
Then you can easily set any color.

And if the SVG has not yet been imported into Scribus,  you can use Inkscape...
#9
Raster and Vector Graphics / Re: Change Color of SVG
Last post by utnik - May 19, 2025, 10:08:25 PM
yes, it is possible (even in 1.6.x and in older versions). but afaik you have to ungroup the .svg first.

utnik
#10
General Discussion / Re: Rotating Objects.
Last post by prcek - May 19, 2025, 09:55:58 PM
Quote from: Nermander on May 19, 2025, 08:59:52 PMI guess instead of writing -45 you could write 360-45.

O.C. I could. But it involves math, although simple I can make mistakes easily.


Quote from: a.l.e on May 19, 2025, 09:37:15 PMWas .. should be as easy...

... might become as easy...

https://bugs.scribus.net/view.php?id=17529

Thank you very much!